S. Mike Linhart and Kris D. Lund 2006 vector digital data Scientific Investigations Map 2006-2949-C Reston, Virginia U.S. Geological Survey https://water.usgs.gov/lookup/getspatial?sim06-2949C_min_tinpts S. Mike Linhart and Kris D. Lund 2006 pdf document Scientific Investigations Map 2006-2949 Reston, Virginia U.S. Geological Survey https://water.usgs.gov/lookup/getspatial?sim06-2949C_min_tinpts http://pubs.water.usgs.gov/sim2006-2949 Point coverage of bathymetry data for Lake Minnewashta in Dickinson Co., Iowa. The U.S. Geological Survey conducted a bathymetric survey of Lake Minnewashta in 2004. This digital, geographically referenced data set was developed by the U.S. Geological Survey to be used with the Lake Bathymetric project, Eastern Field Unit, Iowa City, Iowa. Data collected during the bathymetric survey were input into a geographic information system (GIS) software package, ArcInfo, to create a point coverage representing discrete point locations. This point coverage (among other coverages) was then used to generate a three-dimensional surface representing the lake-bottom elevations. 2004 ground condition Complete None planned -95.132015 -95.119660 43.365072 43.357175 USGS Thesaurus Lakes Bathymetry InlandWaters Hydrology Contours USGS ISO 19115 Topic Category geoscientificInformation inlandWaters environment USGS Metadata Identifier USGS:6b3dc084-b719-4476-adbf-8ba541f81b74 Geographic Names Information System Lake Minnewashta Dickinson County Iowa This digital, geographically referenced data set was developed by the U.S. Geological Survey to be used with the Lake Bathymetric project, Eastern Field Unit, Iowa City, Iowa. The data are released on condition that neither the USGS nor the United States Government may be held liable for any damages resulting from its authorized or unauthorized use. U.S. Geological Survey Greg Nalley Project Chief - Eastern Field Unit Supervisory Hydrologist physical address

P.O. Box 1230

Iowa City Iowa 52244 USA 319-337-4191 319-358-3606 gmnalley@usgs.gov Compilation of this data set prepared in cooperation with Iowa Department of Natural Resources. Microsoft Windows XP Version 5.1 (Build 2600) Service Pack 2; ESRI ArcCatalog 9.1.0.722 Topologically Clean Point coverage of filtered bathymetry data points collected along transects and perimeter using the 200-KHz transducer. Data were filtered, from 7,768 to 2,659 data points, in the data-collection software Hypack Max, prior to generation of this coverage. This coverage was used for input into a TIN model. Accuracy is tested by visual comparison of source with digital data on an interactive computer system. Iowa Department of Natural Resources Unknown 2002 remote-sensing image <http://www.igsb.uiowa.edu/nrgislibx/> Aerial Photo 2002 ground condition None Digital orthophoto quads (DOQ's) were used in further adjusting and smoothing the coverage of the lake boundary. The coverage was overlain on the DOQ and additional vertices were digitized into the arcs at locations corresponding the shoreline shown on the DOQ. Water-surface elevation: Initial measurements determined the elevation of the water surface of Lake Minnewashta referenced to National Geodetic Vertical Datum (NGVD) of 1929 using standard surveying techniques. A reference point (point from which to measure the water surface) elevation was established by leveling from a nearby existing reference mark with a known elevation (provided by Dickinson County Engineers Office). Accuracy of the existing reference mark is unknown. The reference point is located on the concrete outflow structure at the road junction at the lower end of Lower Gar Lake. The elevation of the reference point was found to be 1399.804 ft above NGVD29. The elevation of the reference point was verified by a static GPS survey (using the Ashtech GPS system) with a difference of 0.063 ft. Measuring from the reference point (using a steel tape), the water-surface elevation was found to be 1394.5 ft above NGVD29 on June 7, 2004. 2004 Data collection: Bathymetry data were collected using the Bathymetric Survey System (BSS+5) with a 200-kHZ intelligent depth sounder (IDS) and a differential GPS (Novatel DGPS beacon or omnistar receiver) (Specialty Devices, Inc., 2003, Bathymetric Survey System BSS+5 with omnistar manual: Specialty Devices, Inc., Plano, Texas, 38 p.). The depth sounder emits pulses of sound that are reflected off the lake bottom and are received by a transducer. The differential GPS has a horizontal accuracy of about 1 meter (3.281 ft). Bathymetry and position data were collected and stored in Hypack Max software (ver. 2.12a) (Hydrographic Survey Software, User's Manual, Hypack Max, Coastal Oceanographics, Inc., Middlefield, Conn.). In Hypack Max, the geodetic parameters were set to UTM north, Zone 15, and ellipsoid GRS-1980. Distance (easting and northing) and depth units were both collected in feet. Current limitations of the Bathymetric Survey System (BSS+5) restrict data collection to depths greater than approximately 3.3 ft. A bar check calibration on the echo sounder was performed at the start of each day following established protocols (U.S. Army Corps of Engineers, 1994, Engineering and design: Hydrographic survey EM 1110-2-1003, chap. 9-3, p. 9-4 to 9-9). This was done to ensure that the echo sounder was calibrated correctly. The bar check involves suspending a 2-ft-diameter flat aluminum plate directly below the echo sounder. The suspension line is marked in 5-ft increments. An initial calibration is made at 5 ft by entering the speed of sound in water (based on water temperature) and then adjusting the offset of the transducer in the computer software. The offset is the draft of the transducer below the lake surface. The aluminum plate is then lowered in 5-ft increments (depending on the range of depths expected to be encountered on the day of data collection) and adjustments in the speed of sound are made until depth readings and the depth of the aluminum plate agree to within approximately 0.1 ft. Bathymetry data were collected along planned transect lines that were set-up in Hypack Max using the internal line editor prior to data collection. Transect lines were spaced at 75-ft intervals perpendicular to the long axis of Lake Minnewashta. Depending on boat speed, bathymetry data points were collected at approximately 5- to 10-ft intervals. Data points may be much closer in areas where transect or perimeter runs overlap. Bathymetry data points also were collected while driving the boat once around the perimeter of the lake. The distance of the boat from shore during the perimeter run varied, depending upon the depths encountered, due to the depth limitations of the data-collection equipment. The raw bathymetry data were recorded in Hypack Max as depths (in feet below water surface to the lake bottom). Target points were collected in areas of the lake where it was too shallow to collect data with the BSS+5 system. Target point depths were collected manually, using a measuring device marked in 0.10-ft increments, along with a corresponding easting and northing location. Depending on lake-bottom type and surface conditions of the lake, accuracy of these measurements can vary between 0.05 ft and 0.5 ft. The number and location of target points were based on a judgment made in the field that was thought to be spatially representative of the area. In addition, shore point locations (easting and northing) were collected to define the shoreline of the lake. These locations are collected by touching the bow of the boat to the shoreline at various intervals along the shoreline and recording the position using a bow-mounted GPS antenna. An independent bathymetry data set (in the coverage min_ctrlpts) also was collected over a smaller area of Lake Minnewashta. This control data set was used to estimate precision (repeatability) of the sounding data collected with the echo sounder. For Lake Minnewashta, there were 35 paired data and control points that were located within 1.5 ft of each other with a calculated Root Mean Square Error (RMSE) of 0.28 ft. The control data set also is used to estimate the accuracy of the produced contours. 2004 Post-processing: Bathymetry data were processed using the Hypack Max software. Post-processing involved removing obvious spikes, inputting depths for the time-tagged target points, and editing extraneous points within the shore point files. In addition, tide corrections were applied in Hypack Max to convert raw sounding depths to elevation. The tide file subtracts the depths from the assigned lake-surface elevation (obtained from measurement from reference point elevation to lake water surface). The processed bathymetry data in Hypack Max were sorted and exported to XYZ format. The perimeter and transect bathymetry data were weeded (thinned) to reduce the density of points in one direction (along data-collection transects) to minimize the spatial pull of contours toward the densified lines. Of the original 7,768 data points, 2,659 data points remained. A total of three separate files were exported into XYZ format: (1) transect and perimeter bathymetry data; (2) shore point location data; and (3) the target point data. The XYZ files were then converted to ASCII text files for input into ESRI-ArcGIS (ver. 8.3). The perimeter and transect data were combined into one data set (min_allpts.txt). The file min_allpts.txt contains all processed data points (not weeded) exported from Hypack Max (not including edge and target points). 2004-2005 Generation of Bathymetry Map: The output text files (containing northing, easting, and elevation) were input into an arc macro language (AML) script called CREATEPOINT in ARC to generate three corresponding coverages (min_edgepts, min_tinpts, and min_targpts). The min_edgepts coverage contains the shore point locations. The min_tinpts coverage contains the weeded bathymetry points collected with the depth sounder. The min_targpts coverage contains the bathymetry target points collected manually. The projections for the coverages were then defined in ARC as UTM zone 15, NAD83, and units in feet. To generate contours and calculate lake volume, three-dimensional surfaces (TIN models) were created using 3-D Analyst in ArcMap. The TIN (min_tin) model was generated to create the preliminary contours. The point coverages, min_tinpts and min_targpts, were input into min_tin and triangulated as mass points. Height source was the "elevation" field in the point coverage attribute table. The min_bndelev line coverage was input as a hard line using the "elev" field as the height source (elevation value = 1394.5 ft). The min_bndry coverage (polygon) was input as a hard clip to clip the TIN to the lake shoreline. Another TIN model (min_tinsmooth) was later generated to re-calculate lake volume after the boundary coverages (min_bndry and min_bndelev) were further adjusted using Digital Orthophoto Quads (DOQ's). 2005-2006 Vector Entity point 2659 Point 4 Transverse Mercator 0.999600 -93.000000 0.000000 1640416.666667 0.000000 coordinate pair 0.000005 0.000005 survey feet North American Datum of 1983 Geodetic Reference System 80 6378137.000000 298.257222 National Geodetic Vertical Datum of 1929 0.1 feet Explicit elevation coordinate included with horizontal coordinates min_tinpts.pat Point Attribute Table ARC/INFO(R) GIS Software FID Internal feature number. ESRI Sequential unique whole numbers that are automatically generated. Shape Feature geometry. ESRI Coordinates defining the features. AREA Area of feature in internal units squared. ESRI Area is always zero for point coverages. Values are automatically generated. PERIMETER Perimeter of feature in internal units. ESRI Perimeter is always zero for point coverages. Values are automatically generated. MIN_TINPTS# Internal feature number. ESRI Sequential unique whole numbers that are automatically generated. MIN_TINPTS-ID User-defined feature number. ESRI Whole numbers that are automatically generated. EASTING X coordinate User defined 1073660.54 1076875.95 U.S. Survey Feet 3.281 Based on GPS manufacturers specifications (with differential correction). NORTHING Y coordinate User defined 15756814.07 15759611.47 U.S. Survey Feet 3.281 Based on GPS manufacturers specifications (with differential correction). ELEVATION Lake-bottom elevation User defined 1379.21 1393.71 feet 0.28 An independent bathymetry data set also was collected over a smaller area of Lake Minnewashta. This control data set was used to estimate precision (repeatability) of the sounding data collected with the echo sounder. For Lake Minnewashta, there were 35 paired data and control points that were located within 1.5 ft of each other with a calculated Root Mean Square Error (RMSE) of 0.28 ft. U.S. Geological Survey Michael Ierardi mailing address

P.O. Box 1230

Iowa City Iowa 52244 USA 1-888-275-8747 (1-888-ASK-USGS) mierardi@usgs.gov None The Lake Bathymetric project of the Eastern Field Unit, Iowa Water Science Center, the Water Resources Discipline (WRD), and the U.S. Geological Survey make no guarantee nor offer any warranty concerning the accuracy, condition, or application of the information contained in these geographic data. The burden for determining fitness for use of this data lies entirely with the user. Although these data have been processed successfully on computers of WRD, no warranty, expressed or implied, is made by WRD regarding the use of these data on any other system, nor does the fact of distribution constitute or imply any such warranty. In no event shall the WRD have any liability whatsoever for payment of any consequential, incidental, indirect, special, or tort damages of any kind, including, but not limited to, any loss of profits arising out of the delivery, installation, operation, or support by WRD. Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government. ARCE Full coverage zipped 0.293 https://water.usgs.gov/GIS/dsdl/sim06-2949C_min_tinpts.e00.gz None. This dataset is provided by USGS as a public service. 20201117 U.S. Geological Survey Michael Ierardi IT Specialist mailing and physical address

P.O. Box 1230

Iowa City Iowa 52244 USA 1-888-275-8747 (1-888-ASK-USGS) mierardi@usgs.gov FGDC Content Standards for Digital Geospatial Metadata FGDC-STD-001-1998